Ariens 921014 Specifikace

Owner/Operator ManualModels921011 – Deluxe 24921012 – Deluxe 27921013 – Deluxe 30921014 – Deluxe Track 24921015 – Deluxe Track 27921016 – Deluxe Track

GB - 10Install Discharge Chute and Discharge Chute Rod(921017, 018) (Figure 8, 9, 10 and 11)1. Grease underside of discharge chute ring (if not alread

GB - 11 9. Connect the chute lock cable to the lock arm by fitting the cable ball end into the slot on the lock arm and then insert the chute lock cab

GB - 12Check Function of Dual Handle InterlockWithout the engine running, press down (engage) both clutch levers. Release attachment clutch lever. Att

GB - 131. Attachment Clutch Lever2. Speed Selector3. Traction Drive Clutch Lever4. Remote Wheel Lock (012, 013, 020)5. Deflector Remote Control (013,

GB - 141. Skid Shoe2. Clean-Out Tool3. Remote Discharge Chute Deflector (013, 016, 017, 018, 020)4. Manual Discharge Chute Deflector (011, 012, 014, 0

GB - 151. Oil Drain2. Fuel Shut-Off Valve3. Primer Bulb4. Recoil Starter Handle5. Throttle (Engine Stop)6. Choke Control Knob7. Ignition Key (Push/Pul

GB - 16CONTROLS AND FEATURESSee CONTROLS and FEATURES on page 13 for all Controls and Features locations.Dual Handle Interlock When Attachment Clutch

GB - 17Primer BulbPushing the primer bulb in adds fuel for easier engine start. Refer to Starting and Shut Off on page 22.Speed Selector (012, 013, 01

GB - 18Snow Clean-Out Tool(Figure 16)To clear the discharge chute:1. Shut off the engine.2. Wait 10 seconds and make sure impeller blades have stopped

GB - 19IMPORTANT: DO NOT force frozen chute controls. If frozen, take to warm place until controls are free.Discharge Chute Crank (921011, 012, 013, 0

GB - 2SAFETY. . . . . . . . . . . . . . . . . . . . . . . . . . 4ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . 8CONTROLS and FEATURES . . . .

GB - 20Skid ShoesThe skid shoes control the distance between the scraper blade and the ground. Adjust skid shoes equally to keep blade level with the

GB - 21GASOLINEIMPORTANT: ALWAYS use gasoline that meets the following guidelines:• Clean, fresh gasoline.• A minimum of 87 octane/87 AKI (91 RON). Hi

GB - 22STARTING AND SHUT OFFIMPORTANT: Allow unit and engine to adjust to the outdoor temperature before clearing snow. Before shut-off, run the attac

GB - 23SNOW REMOVALIMPORTANT: Allow unit and engine to adjust to the outdoor temperature before clearing snow.NOTE: Attachment clutch should be engage

GB - 24MAINTENANCE SCHEDULEThe chart below shows the recommended maintenance schedule that should be performed on a regular basis. More frequent servi

GB - 25CHECK AUGER GEARCASE IMPORTANT: Proper oil level must be maintained.Gear cases are filled to the correct level at the factory. Unless there is

GB - 26SCRAPER BLADEIMPORTANT: Damage to auger/impeller housing will result if blade wears down too far.Scraper blade is adjustable to compensate for

GB - 276. Repeat steps 2 – 4 while watching cable to remove slack.7. Check function of remote wheel lock. If wheel lock does not function properly, ta

GB - 28If chute does not rotate freely:Tighten the cable by loosening the forward adjustment nut, and then tightening the rear adjustment nut against

GB - 29d. Stop unit.e. Shift speed selector into first reverse speed.f. Engage the traction clutch. Unit should move backward.g. Shut off unit.8. Adju

GB - 3• Record Unit Model and Serial numbers here.• Record Engine Model and Serial numbers here.PRODUCT REGISTRATIONThe Ariens dealer must register th

GB - 30• If roller is more that 7/8 in. (22.2 mm) from frame, loosen idler adjustment nut and move idler away from the belt, tighten adjustment nut an

GB - 31Check Attachment Brake(Figure 40)1. With the clutch lever disengaged, brake pad must contact attachment belts. With clutch lever engaged, brake

GB - 324. To adjust traction clutch (Figure 43):a. With the traction drive clutch lever disengaged, loosen the jam nut on the cable adjuster.b. Turn t

GB - 338. Remove hex bolts securing housing to frame (two on each side). Tip housing and frame apart on pivot pin (Figure 45).9. Remove attachment dri

GB - 343. Pull idler away from traction drive belt and remove belt from idler pulley, engine sheave and driven pulley (it may be necessary to turn eng

GB - 35TRACK TENSION ADJUSTMENT(921014, 015, 016)Check the track tension by applying pressure on the track midway between the upper and rear track rol

GB - 36SHORT TERMIMPORTANT: NEVER spray unit with high pressure water or store unit outdoors.Run with attachment clutch engaged a few minutes after ea

GB - 37 TROUBLESHOOTINGPROBLEM PROBABLE CAUSE CORRECTION Engine will not crank/start.1. Fuel tank is empty.2. Fuel shut-off valve closed.3. Build up o

GB - 38SPECIFICATIONSModel Number 921011 921012 921013DescriptionDeluxe 24 Deluxe 27 Deluxe 30EngineEngineBriggs & Stratton 1150 Snow SeriesBriggs

GB - 39SPECIFICATIONSModel Number 921014 921015 921016DescriptionDeluxe Track 24 Deluxe Track 27 Deluxe Track 30EngineEngineBriggs & Stratton 1150

GB - 4SAFETY ALERTSLook for these symbols to point out important safety precautions. They mean:Attention! Personal Safety Is Involved!Become Alert!

GB - 40SPECIFICATIONSModel Number 921017 921018 921019 921020Description Deluxe 24 Platinum Deluxe 30 PlatinumDeluxe 24 Deluxe 30EngineEngine Model B

ARIENS COMPANYGRAVELY® | STENS® | LOCKE® | NATIONAL® | BYNORM® | EVERRIDE® | GREAT DANE® Snow_2008Page 41Three-Year Limited Sno-Thro® WarrantyAriens

ARIENS COMPANYGRAVELY® | STENS® | LOCKE® | NATIONAL® | BYNORM® | EVERRIDE® | GREAT DANE® Snow_2008Page 42Limitations• Batteries are warranted only fo

Protective Floor MatProtects oor from rust, dirt and snow melt.Ariens Company655 West Ryan StreetBrillion, WI 54110-1072920-756-2141Fax 920-756-2407

GB - 51. WARNING!2. DANGER! 3. DANGER!SAFETY RULESRead, understand, and follow all safety practices in Owner/Operator Manual before beginning assembly

GB - 6DO NOT operate near drop-offs, ditches, or embankments. Unit can suddenly turn over if a wheel is over the edge of a cliff or ditch, or if an ed

GB - 7Check clutch and brake operation frequently. Adjust and service as required. All motion of drive wheels and auger/impeller must stop quickly whe

GB - 8PACKAGE CONTENTS ASSEMBLYTools Required:•Pliers• Open-End Wrenches: 3/8, 7/16, 1/2, 9/16 in. and/or Adjustable Wrench• Tire GaugeASSEMBLYWARNING

GB - 9Unfold Handlebar (Figure 5)1. Remove the lower and loosen the upper hardware on the handlebar assembly.2. Loosen the hardware on the shift rod.3