Ariens ProZoom 99480600-1952S Specifikace

Pro Zoom™Owner/Operator ManualManuel Du Propriétaire/UtilisateurENGLISHFRANÇAIS03837300 12/08Printed in USAModels99480600 – 1952S

GB - 10Daily Operating Checklist• Make sure all necessary guards and shields are safely and securely attached. Check for loose, missing, or damaged pa

GB - 11Mounting and Dismounting Machine Safely1. Step on operator’s platform (A) at the rear of machine to mount the machine.2. Park machine safely. (

GB - 12Setting Cutting HeightHOLE LOCATIONSTo adjust the rear height of cut, use the chart above and match the hole locations on the chart up to the h

GB - 13Testing PTO Switch1. Stand on operator’s platform with motion control levers in the neutral position.2. Lock park brake.3. Pull PTO switch up t

GB - 14Using the PTOEngage PTO:1. Stand on operator’s platform with motion control levers in the neutral position.2. Start engine.3. Release park brak

GB - 15Forward and Reverse Motion:1. Move throttle lever to the fast position.2. Unlock park brake.3. Push motion control levers forward to begin forw

GB - 16Sharp Right Turn:MX12793• Push left motion control lever forward and pull right motion control lever rearward at the same time.Starting Engine1

GB - 17Using Pump Free-Wheel ValvesNOTE: The pump free-wheel valves must be turned fully clockwise (closed) during normal machine operation.When the m

GB - 18Servicing Your MachinePlease use the following timetables to perform routine maintenance on your machine.Servicing EngineSee engine manufacture

GB - 19Lubricating Front Caster Spindles and Wheels• Lubricate two spindle grease fittings (A) and two wheel grease fittings (B).Lubricating Pump Idle

GB - 2Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Assembly. . . . . . . . . . . . . . . . . . . .

GB - 20Service Engine Avoid FumesEngine Oil Use oil viscosity based on the expected air temperature range during the period between oil changes.Use oi

GB - 2110. Apply a film of clean engine oil to gasket of new filter.11. Install filter. Turn filter clockwise until gasket makes contact with mounting

GB - 221. Park machine safely. (See Parking Safely in the SAFETY section.)2. Allow engine to cool.3. Slide hose clamps (A) away from fuel filter (B).4

GB - 2313. Unlock park brake.14. Cycle motion control levers forward and rearward several times. Check for leaks around filter.15. Stop engine. Check

GB - 24Removing Traction Drive Belt:1. Park machine safely. (See Parking Safely in the SAFETY section.)2. Remove mower deck drive belt. (See Replacing

GB - 25Adjusting Motion Control Return to Neutral (RTN) Linkages:1. Stop engine.2. Lock park brake.3. Lift machine with a safe lifting device centered

GB - 26Adjusting Forward and Reverse SpeedsAdjusting Forward Speed:1. Park machine safely. (See Parking Safely in the SAFETY section.)Picture Note: Ar

GB - 27Service MowerRemoving and Installing Mower Deck ShieldRemoving Mower Deck Shield:1. Park machine safely. (See Parking Safely in the SAFETY sect

GB - 28Installing Mower Deck Drive Belt:NOTE: If necessary, see drive belt installation label on mower deck.1. Install replacement drive belt (A) as s

GB - 29Replacing Mower Blades1. Remove blade bolt (A), three 1/4 in. washers (C) and blade (B). 2. Install replacement blade:• Blade wing must face to

GB - 3PRODUCT REGRISTRATIONThe Ariens dealer must register the product at the time of purchase. Registering the product will help the company process

GB - 30Checking the Battery (Sealed Batteries)NOTE: Do not attempt to open, add fluid or service battery. Any attempt to do so will void warranty.• Ke

GB - 31M71044A. Booster BatteryB. Disabled Vehicle Battery1. Connect positive (+) booster cable to booster battery (A) positive (+) post (C). 2. Conne

GB - 32Filling Fuel TankFill fuel tank at the end of each day’s operation to prevent condensation and freezing during cold weather.1. Park machine saf

GB - 33Tightening Rear Drive Wheel Hardware1. Tighten rear wheel nuts to 102 N•m (75 lbf-ft).2. Tighten wheel nuts in numbered sequence shown for safe

GB - 34Cleaning and Repairing Metal SurfacesCleaning:Follow automotive practices to care for your vehicle painted metal surfaces. Use a high-quality a

GB - 35Electrical SystemEngine Runs Rough or Stalls• Plugged fuel filter.• Plugged air intake system.• Fuel cap vent dirty.• Stale or improper fuel/fu

GB - 36MachinePark BrakeSteeringMower DeckIf CheckExcessive Machine Vibration• Engine speed too slow.• Deck drive belt not tensioned correctly.• Mower

GB - 37Storing SafetyPreparing Machine for Storage1. Repair any worn or damaged parts. Replace parts if necessary. Tighten loose hardware.2. Repair sc

GB - 38SPECIFICATIONSModel Number 994806Model Pro Zoom 1952SEngineEngine KawasakiEngine Model Number FH580VEngine Dispalcement – cc (in3) 580 (35.7)Ai

GB - 39Recommended LubricantsEngine Oil – See Applicable Engine ManualHydraulic Oil 5W-50 or 15W-50 All Synthetic OilGrease: (This may change for high

GB - 4REQUIRED OPERATOR TRAININGOriginal purchaser of this unit was instructed by the seller on safe and proper operation. If unit is to be used by so

GB - 40Service MiscellaneousWiring Schematics

GB - 41Service MiscellaneousHydraulic SchematicsA. Left Hydrostatic Pump AssemblyB. Pump BlockC. Charge PumpD. System Charge Check Shock Valve (Revers

ARIENS COMPANYGRAVELY® | STENS® | LOCKE® | NATIONAL® | BYNORM® | EVERRIDE® | GREAT DANE® Com_Lawn_200842 of 43Ariens Company (Ariens) warrants to the

ARIENS COMPANYGRAVELY® | STENS® | LOCKE® | NATIONAL® | BYNORM® | EVERRIDE® | GREAT DANE® Com_Lawn_200843 of 43To find an Ariens or Gravely authorized

Ariens Company655 West Ryan StreetBrillion, WI 54110-1072USA920-756-2141Fax 920-756-2407www.ariens.com

GB - 5Emission Control System Certification LabelNOTE: Tampering with emission controls and components by unauthorized personnel may result in severe

GB - 6Checking Mowing Area• Evaluate the terrain to determine what accessories and attachments are needed to properly and safely perform the job. • Cl

GB - 7• Keep all movement on slopes slow and gradual. Do not make sudden changes in speed or direction, which could cause the machine to roll over.• U

GB - 8Prevent Fires• Remove grass and debris from engine compartment and muffler area, before and after operating machine, especially after mowing or

GB - 9AssemblyConnect HandlesThe handles are disconnected and rotated forward during shipment to allow proper fit in the shipping container.1. Rotate