Owner/Operator ManualModels911207 – Pro21XD911214 – Pro21XD CARBWalk Behind Lawn Mower00661700B 1/07Printed in USATransfer model & serial number l
GB - 101. Handlebars2. Speed Control Knob 3. Integrated Engine/Blade and Wheel Drive Control 4. Oil Fill/Dipstick5. Fuel Tank and Cap6. Air Filter7. P
GB - 11CONTROLS AND FEATURESSee Figure 7 for locations.Engine/Blade ControlThe engine/blade control must be held against the handlebar to start the en
GB - 12CUTTING HEIGHT ADJUSTMENTFront WheelRemove the lock pin from the left front wheel and then remove the wheels and axle from the unit. Install th
GB - 13Rear WheelTo change cutting height, move cutting height levers one notch at a time on each wheel to set desired height.NOTE: Each wheel on mowe
GB - 14OPTIONAL CONTROLSPrimer BulbPush the primer bulb in to add fuel for easier engine start.Wheel Drive Control (self-propelled models)NOTE: Engine
GB - 15To Bag1. Shut off unit.2. Install side discharge cover (Figure 14).3. Lift rear door.4. Hook grass bag frame on mounting flange.5. Lower rear d
GB - 16EMERGENCY STOPPINGTo stop the mower in an emergency: 1. Release the engine/blade control.2. Release the wheel drive control (self-propelled mod
GB - 17Ariens Dealers will provide any service, parts or adjustments which may be required to keep your unit operating at peak efficiency. Should engi
GB - 183. Remove bolt, lock washer, flat washer and blade from shaft.To install blade: 1. Replace blade, flat washer, lock washer and bolt on shaft.2.
GB - 19CHECK DRIVE BELT (self-propelled models)Check drive belt and replace if worn or damaged. See DRIVE BELT REPLACEMENT (self-propelled models) on
GB - 2Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Assembly . . . . . . . . . . . . . . . . . . . . . . . . 8Controls and Features .
GB - 20SERVICE POSITIONPut unit into service position for easy access to underneath the deck.1. Place unit on a flat, level surface.2. Disconnect spar
GB - 21To install the drive belt:IMPORTANT: Be sure the belt seats in idler and pulley grooves with the idler touching the back (flat) side of belt.1
GB - 22To adjust:1. Move the wheel drive cable adjuster up or down the handlebar. See Figure 24.To increase traction and speed, move the cable adjuste
GB - 23TROUBLESHOOTINGPROBLEM PROBABLE CAUSE CORRECTION Engine will not start1. Fuel tank empty or low.2. Fuel shutoff valve closed.3. Spark plug wire
GB - 24SERVICE PARTSAlways use genuine Ariens parts to keep your mower running like new. Description Part NumberAir Filter 21541000 Spark Plug 215408
GB - 25SPECIFICATIONSModel Number 911207 911214Description Pro21XD Pro21XDCARBLength - in. (cm) 62.5 (158.8) 62.5 (158.8)Height - in. (cm) 40.6 (103.1
Ariens Company • 655 W. Ryan St, P.O. Box 157 • Brillion, WI 54110-0157• (920) 756-2141 • www.ariens.comALW2-62905Ariens Limited Warranties2-Year Limi
Ariens Company • 655 W. Ryan St, P.O. Box 157 • Brillion, WI 54110-0157• (920) 756-2141 • www.ariens.comALW2-62905Exceptions, Limitations, ExclusionsT
Ariens Company655 West Ryan StreetP.O. Box 157Brillion, WI 54110-0157920-756-2141Fax 920-756-2407www.ariens.com
GB - 34. Explain recommended lubrication and maintenance. Advise customer on adjustments. Remind customer to change oil in 4 cycle engine crankcase af
GB - 4SAFETY DECALS AND LOCATIONSALWAYS replace missing or damaged safety decals. Refer to Figure 2 for safety decal locations.1. DANGER! TO AVOID SER
GB - 5• all safety decals.Clear work area of stones, sticks, wire and foreign objects which might be picked up and thrown. Tall grass can hide obstacl
GB - 6To reduce fire hazard and overheating, keep equipment free of grass, leaves, debris or excessive lubricants.Use extra care when approaching blin
GB - 7Accidental engine start up can cause death or serious injury. Except where specifically recommended, ALWAYS stop engine, remove key (electric st
GB - 8CARTON CONTENTSASSEMBLYFigure 41. Remove mower and handlebar from carton.2. Install the handlebar and braces on the handlebar brackets with the
GB - 93. Install the drive cover with three hex bolts and lock washers. Make sure the plate does not pinch any cables.4. Connect the engine/blade cont
Komentáře k této Příručce